After repair imei factory reset
Selected model: OPPO CPH2185 (Oppo A15)
Operation: Repair
Software version: 2.10
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM22 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA3DF89C9, 0xF1A81E49, 0x66855969, 0xAEB75377
Get Chip ID... [MT6765]
Get SOC ID... [97C37955B54A85970962D95F7B941177B01640548B3E68F961EEDC753A626DC8]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [23]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68423861503E030093C6EAB71D
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x90014A68423861503E030093C6EAB71D
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0001000000 (16,00Mb)
EMMC_USER : 0x0747C00000 (29,12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232,00Kb)
EXT_RAM : 0x0080000000 (2,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Board : oppo6765
Board Platform : MT6765
Build ID : QP1A.190711.020
Build Date : Fri Oct 15 20:59:26 CST 2021
Display ID : QP1A.190711.020 release-keys
Security Patch : 2021-10-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 8604xxxxxxxxxxxx
IMEI 2: 8604xxxxxxxxxxxx
Repairing IMEI...
IMEI 1: 3585xxxxxxxxxxxx
IMEI 2: 3585xxxxxxxxxxxx
Write IMEI [NVDATA]... OK
Load partiton for patching... OK
Patching CERT... OK
Save patched partiton... OK
Unlock bootloader... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
by Gsm_Moderator
Selected model: OPPO CPH2185 (Oppo A15)
Operation: Repair
Software version: 2.10
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM22 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA3DF89C9, 0xF1A81E49, 0x66855969, 0xAEB75377
Get Chip ID... [MT6765]
Get SOC ID... [97C37955B54A85970962D95F7B941177B01640548B3E68F961EEDC753A626DC8]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [23]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68423861503E030093C6EAB71D
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x90014A68423861503E030093C6EAB71D
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0001000000 (16,00Mb)
EMMC_USER : 0x0747C00000 (29,12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232,00Kb)
EXT_RAM : 0x0080000000 (2,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Board : oppo6765
Board Platform : MT6765
Build ID : QP1A.190711.020
Build Date : Fri Oct 15 20:59:26 CST 2021
Display ID : QP1A.190711.020 release-keys
Security Patch : 2021-10-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 8604xxxxxxxxxxxx
IMEI 2: 8604xxxxxxxxxxxx
Repairing IMEI...
IMEI 1: 3585xxxxxxxxxxxx
IMEI 2: 3585xxxxxxxxxxxx
Write IMEI [NVDATA]... OK
Load partiton for patching... OK
Patching CERT... OK
Save patched partiton... OK
Unlock bootloader... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
by Gsm_Moderator
