Selected model: Meizu M612H (M5s/M5s Mini)
Operation: Repair
Software version: 2.11
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0337
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6735]
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM188 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0337
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6735]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Load DownloadAgent... OK
ME_ID = 0x2D6D665C, 0xE2B04B41, 0x9BF96CF5, 0x78091474
Get sec config... OK [00000000]
Get BROM version... OK
Search DA... OK [10]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Check bootloader answer... OK
Wait for answer from bootloader... OK
Wait for hw detection... OK
Wait DA version... v4.2
Send BROM version... OK
Send storage config... OK
SyncBmtInfoWithDA... OK
Set params... OK
Read flash info... OK
EMMC_ID: 0x150100524531424D4207500697CFF39F
Load EMI from phone... OK
Init DRAM... OK
Enable DRAM... OK
Sync with DA... OK
Wait for DA H/W detection... OK
EMMC INFO:
EMMC_ID : 0x150100524531424D4207500697CF939F
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x03A3E00000 (14,56Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128,00Kb)
EXT_RAM : 0x00C0000000 (3,00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek DA USB VCOM (Android),usb2ser.sys,3.0.1504.0]
High Speed USB detected at COM124
Open port... OK
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : Meizu
Product Manufacturer : Meizu
Product Model : 1612
Product Name : meizu_M5s
Product Device : M5s
Product Board : M5s
Board Platform : MT6735
Meizu Model : M612H
Build ID : MRA58K
Build Date : Thu Mar 7 17:48:41 CST 2019
Display ID : Flyme 6.3.1.0G
Security Patch : 2018-02-05
Version SDK : 23
Version Release : 6.0
Version Codename : REL
Firmware Version : 1551951703
Read partition nvram... OK
Read partition nvdata... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 86374xxxxxxxxxxx
IMEI 2: 86374xxxxxxxxxxx
Repairing IMEI...
IMEI 1: 86372xxxxxxxxxxx
IMEI 2: 86372xxxxxxxxxxx
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Check parametres... OK
Write partition "nvdata"... OK
Check parametres... OK
Write partition "nvram"... OK
Repair Security done!
Thanks Pandora box team
Operation: Repair
Software version: 2.11
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0337
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6735]
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM188 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0337
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6735]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Load DownloadAgent... OK
ME_ID = 0x2D6D665C, 0xE2B04B41, 0x9BF96CF5, 0x78091474
Get sec config... OK [00000000]
Get BROM version... OK
Search DA... OK [10]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Check bootloader answer... OK
Wait for answer from bootloader... OK
Wait for hw detection... OK
Wait DA version... v4.2
Send BROM version... OK
Send storage config... OK
SyncBmtInfoWithDA... OK
Set params... OK
Read flash info... OK
EMMC_ID: 0x150100524531424D4207500697CFF39F
Load EMI from phone... OK
Init DRAM... OK
Enable DRAM... OK
Sync with DA... OK
Wait for DA H/W detection... OK
EMMC INFO:
EMMC_ID : 0x150100524531424D4207500697CF939F
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x03A3E00000 (14,56Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128,00Kb)
EXT_RAM : 0x00C0000000 (3,00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek DA USB VCOM (Android),usb2ser.sys,3.0.1504.0]
High Speed USB detected at COM124
Open port... OK
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : Meizu
Product Manufacturer : Meizu
Product Model : 1612
Product Name : meizu_M5s
Product Device : M5s
Product Board : M5s
Board Platform : MT6735
Meizu Model : M612H
Build ID : MRA58K
Build Date : Thu Mar 7 17:48:41 CST 2019
Display ID : Flyme 6.3.1.0G
Security Patch : 2018-02-05
Version SDK : 23
Version Release : 6.0
Version Codename : REL
Firmware Version : 1551951703
Read partition nvram... OK
Read partition nvdata... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 86374xxxxxxxxxxx
IMEI 2: 86374xxxxxxxxxxx
Repairing IMEI...
IMEI 1: 86372xxxxxxxxxxx
IMEI 2: 86372xxxxxxxxxxx
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Check parametres... OK
Write partition "nvdata"... OK
Check parametres... OK
Write partition "nvram"... OK
Repair Security done!
Thanks Pandora box team
