Selected model: BQ UNKNOWN Select mtk cpu platform
Operation: Repair
Software version: 2.8
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0699
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6739]
Get sec config... OK [00000000]
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM210 [BROM]
Open port... OK
Get HW code from device... 0699
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6739]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x78A7A81F, 0xA7074140, 0x32EB2CA3, 0x66FA93A6
Get Chip ID... [MT6739]
Get SOC ID... [3209FCCF48CB3AA151C015F0255DA6685E0C07758F470709E41AE0BF465617F9]
Get sec config... OK [00000000]
Load DownloadAgent... OK
Search DA... OK [0]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x8801034E436172642022D20077227483
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x8801034E436172642022D20077227483
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x01CE100000 (7,22Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128,00Kb)
EXT_RAM : 0x0040000000 (1,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Read product info... OK
Product Brand : INOI
Product Manufacturer : teksun
Product Model : INOI_3
Product Name : INOI_3
Product Device : t939ha_v1_ao_tyc_gm50v1_go
Product Board : t939ha_v1_ao_tyc_gm50v1_go
Board Platform : MT6739
Build ID : O11019
Build Date : 2018年 08月 02日 星期四 11
Display ID : t939ha_v1_ao_tyc_gm50v1_go_v18_2
Security Patch : 2018-07-05
Version SDK : 27
Version Release : 8.1.0
Version Codename : REL
Firmware Version : 1533182444
Read partitions info from phone... OK
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 359521xxxxxxxxxx
IMEI 2: 000000000000000
Repairing IMEI...
IMEI 1: 359521xxxxxxxxxx
IMEI 2: 359521xxxxxxxxxx
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
Operation: Repair
Software version: 2.8
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0699
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6739]
Get sec config... OK [00000000]
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM210 [BROM]
Open port... OK
Get HW code from device... 0699
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6739]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x78A7A81F, 0xA7074140, 0x32EB2CA3, 0x66FA93A6
Get Chip ID... [MT6739]
Get SOC ID... [3209FCCF48CB3AA151C015F0255DA6685E0C07758F470709E41AE0BF465617F9]
Get sec config... OK [00000000]
Load DownloadAgent... OK
Search DA... OK [0]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x8801034E436172642022D20077227483
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x8801034E436172642022D20077227483
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x01CE100000 (7,22Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128,00Kb)
EXT_RAM : 0x0040000000 (1,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Read product info... OK
Product Brand : INOI
Product Manufacturer : teksun
Product Model : INOI_3
Product Name : INOI_3
Product Device : t939ha_v1_ao_tyc_gm50v1_go
Product Board : t939ha_v1_ao_tyc_gm50v1_go
Board Platform : MT6739
Build ID : O11019
Build Date : 2018年 08月 02日 星期四 11
Display ID : t939ha_v1_ao_tyc_gm50v1_go_v18_2
Security Patch : 2018-07-05
Version SDK : 27
Version Release : 8.1.0
Version Codename : REL
Firmware Version : 1533182444
Read partitions info from phone... OK
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 359521xxxxxxxxxx
IMEI 2: 000000000000000
Repairing IMEI...
IMEI 1: 359521xxxxxxxxxx
IMEI 2: 359521xxxxxxxxxx
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!